💧为耽搁了手持打码机进行率平均寿命，提高技能进行率率和无缺率，压减不足率。现将我平台手持打码机经常保護及医养小常识与达人分享视频。
ಌIn order to prolong the service life of the jet printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
𒊎1、因打标机充分利用的胶印油墨和浓缩咖啡剂很是随便灭掉，因此须在典范通风处安顿好打标机，事隔阴燃、烈焰和消除静电。
💯1. Because the ink and diluent used in the jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、最好不要残存胶印油墨、洗濯剂浸水过的碎布和碎纸条在打标机旁。
𝓡2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the printer.
3、 请勿在喷码器一圈其他没有烟瘾，应吊件“应对炊火”和“易然uv墨水”标出在喷码器一圈。
💛3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" and "Flammable Ink" should be hung near the printer.
4、在激光打码机二侧计划二腐蚀碳灭古兵器（相比远接连10米）。
❀4. Place a carbon dioxide fire extinguisher near the jet printer (the longest distance is 10 meters).
二、喷码直流电机气毗连注重细节事变
ꦯII. Notices for Electrical Connection of Jet Coder
♐1、 连接到220V单选外接电压开关（含地线），必需合理利用trw外接电压开关线，毗连到结实牢固的、试验装置有地线的外接电压开关电源插座上。
⛎1. When connected to 220V single power supply (including ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
🤪2、 地线的毗连必定严格按照关与划界。倘若地线发动战争不良现象，有可能构成打码机主板芯片的损毁或引起其它替伏高风险。
⭕2. The connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printer motherboard or other potential hazards.
三、通常保障安养遵循事变
3. Daily maintenance matters needing attention
1. 合理利用打标机吸塑油、精提剂时对禁止配戴隐型眼睛。
🍌1. It is absolutely forbidden to wear contact lenses when using ink and diluent of jet printer.
2. 当曾加uv墨水或高浓剂控制时，倡导根据抗相转移催化剂棉手套和防护系统镜。
ꦫ2. Anti-solvent gloves and protective goggles are recommended when adding ink or diluent.
3. 打码机在夏天医养系统进程下述：
♛3. The daily maintenance process of the jet printer is as follows:
武汉喷码器保护区保养首可是管道、打印机喷头保养：
🔜Maintenance of Beijing Printer is mainly pipeline and nozzle maintenance.
🐷a) 墨汁刷新：先将液压滤油器里的墨汁全数抽暇，精浓剂植入墨汁罐工作1h后全数 挤兑，第三步参与精浓剂工作0.5h后全数挤兑，参与原车墨汁。呼吁机械性每采用半年暂停第一次墨汁刷新，保护武器工作双倍不改变。（挤出的废渣不呼吁两次采用，避免止构成液压滤油器梗塞） a) 喷淋头洗濯：对不还具有拒绝洗濯药用价值的打码机，呼吁每天都旋钮机时洗濯，以 确认机赢得高品行的复印机结局。在喷淋头以下制定计划储槽，用共用洗桶装入精浓剂，点射喷口、充点极、论文检测极、高压变压器偏转板上的墨渍暂停洗濯，关注着就不要让精浓剂溅进出口眼及皮膚，洗濯卫生后，拿纸巾将喷淋头各处件的洗濯剂晾干。
🍬(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
♌b) 研究生调剂墨线：若创造墨线背离收受对接器，停掉喷咀买通，用公供洗瓶插足少 许浓缩造成剂至喷咀帽，平繁买通3次开始的，如墨线一种在一致的社会价值则需停掉劳务费用冶疗喷腔。墨线规范起来：正冲收受对接器观察，墨线喷入收受对接器三份之六处且略左。（侧看墨线在收受对接器正上方间）
💞B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
🌠二）打码机永劫间宕机后的保护性 一点一场宕机，不要之时在，只需该打码机在本周内待机机器运行2次，并张开墨线最好是提升机器运行或印刷油墨发布一些分钟，如此便就能够用多长次短宕机替代永劫间的宕机。
🐟2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）打标机停用的时候为8-十天：对喉管和喷淋头止住一些洗濯，喷淋头朝上分配，防范打印墨水流入。
♈1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle is placed upward to prevent ink reflux.
🔜2）打码机停用时会跨跃半个月：此情此景须得将机械性内的墨汁直接排放后插足萃取剂运行的，终了后把水嘴朝上设置，避免墨汁回到。
🥃2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must be discharged and run with diluent. After that, the sprinkler head should be placed upward to prevent the ink from flowing back.
𒁃3）永劫间关机后启用打标机更加重视事变 关机8-30多天打标机的启用，若有要用，核对一下墨线改变性。停止工作一下分之五钟的喷管买通。
🥃3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of the ink line. Make a 5-minute nozzle pass.
4)关机那时候跨越式30天
4) Over 30 days of downtime
ꦺ将聚氨酯保温管中的uv墨水排完。参与溶缩剂日常正常暖机1个个钟头，疏浚因永劫间进行时而梗塞的聚氨酯保温管。溶缩剂日常正常暖机时可进行多次4分种的激光喷口买通。溶缩剂日常正常暖机终了后座完聚氨酯保温管，参与新uv墨水，再买通激光喷口5分钟种使墨线价值倍加一致。
▨Empty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minutes to make the ink line position more stable.
ꦗ5) 手持喷码器维护怡养周期公式。 每五天对手持喷码器输送管暂停有有一次性性查抄，不一定是腐蚀、讨论稿不一定是晃动 改换过滤程序器。该使用视工作生态而定，如有害气体较大的至少相隔4个月时间改换有有一次性性，一半工作生态下还应相隔11个大概月时间暂停有有一次性性。机械厂间接吸尘。该使用至少还应相隔1个大概月时间暂停有有一次性性。
𓂃5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printer, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、打标机的耗费材料的充分利用和保管重视起来事变
ꦬIV. Notices for Use and Maintenance of Consumables for Printers
ꦅ1、激光打码机回收利用的耗损品蒸发性强，存储时，应大于35度，严防低溫，阔别多年火源计划、热环境，须得封密杰出的并存贮在荫凉通风处（封停性好的厚壁铁柜里存贮）。
ꦬ1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cabinet with good sealing).
2、喷码器的耗损品的存放期是一个年。
ꦬ2. The shelf life of consumables of jet printer is one year.
3、手持喷码机的耗损品严酷匹配名牌采取，没法采取代替品，要不然会给史诗装备构成紧迫隐患。
🐬3. The consumables of the jet printer should be strictly used in accordance with the brand, and no substitute should be used, otherwise serious damage will be caused to the equipment.